Free tool · ISA arborist exam · Trees and Construction
DBH & root zone calculator
Enter the trunk circumference or diameter at 4.5 feet. Get DBH, the critical root zone radius and a tree protection zone sized for species tolerance and age.
DBH
20.1 in
50.9 cm
Critical root zone radius
20.1 ft
6.1 m · a circle 40.1 ft across, 1,263 ft²
Tree protection zone radius
20.1 ft
6.1 m · 1 ft per inch of DBH
Radii are measured from the face of the trunk. Local tree ordinances override these rules of thumb.
How to measure DBH
DBH (diameter at breast height) is the trunk diameter 4.5 feet above the ground. Wrap a tape around the trunk at that height and divide the circumference by pi (3.14), or use a diameter tape, which is printed so it reads diameter directly. The awkward trunks are where people go wrong:
- Slope: Portland’s guide measures 4.5 feet along the trunk from the midpoint of the uphill and downhill sides. Foresters often start from the uphill side, so note which you used.
- Leaning trunk: wrap the tape at right angles to the trunk, not parallel to the ground.
- Bump, burl or branch at 4.5 feet: measure the narrowest point between 4.5 feet and the ground.
- Trunk splits below 4.5 feet: for a single tree, measure the narrowest point below the split. Tree ordinances often use their own multi-stem rule; Portland, for example, adds the largest trunk’s diameter to half the diameter of each other trunk.
Critical root zone: the common rule and its variants
The most widely used rule gives the critical root zone 1 foot of radius for every inch of DBH, measured from the face of the trunk. Washington State DOT’s standard tree protection detail uses exactly that. Some guides ask for more: the Chattanooga Tree Commission’s builder BMPs use 1.5 feet per inch with a 6-foot minimum, and some codes simply use the dripline. Use the rule your permit or ordinance names.
| DBH | CRZ radius (1 ft/in) | CRZ radius (1.5 ft/in) | Fenced circle across (1 ft/in) |
|---|---|---|---|
| 4 in | 4 ft | 6 ft | 8 ft |
| 6 in | 6 ft | 9 ft | 12 ft |
| 8 in | 8 ft | 12 ft | 16 ft |
| 10 in | 10 ft | 15 ft | 20 ft |
| 12 in | 12 ft | 18 ft | 24 ft |
| 16 in | 16 ft | 24 ft | 32 ft |
| 20 in | 20 ft | 30 ft | 40 ft |
| 24 in | 24 ft | 36 ft | 48 ft |
| 30 in | 30 ft | 45 ft | 60 ft |
| 36 in | 36 ft | 54 ft | 72 ft |
| 42 in | 42 ft | 63 ft | 84 ft |
| 48 in | 48 ft | 72 ft | 96 ft |
Tree protection zone by species tolerance and age
The tree protection zone is the area you actually fence and keep equipment, storage and digging out of. A widely used method from Matheny and Clark’s Trees and Development (ISA, 1998) scales it to how well the species tolerates construction and how old the tree is, in feet of radius per inch of DBH:
| Species tolerance | Young | Mature | Over-mature |
|---|---|---|---|
| Good | 0.5 | 0.75 | 1 |
| Moderate | 0.75 | 1 | 1.25 |
| Poor | 1 | 1.25 | 1.5 |
Roots often spread well past these circles. The zones mark the minimum area to protect, not the edge of the root system.
Why it matters for the ISA exam
Trees and Construction is 9% of the ISA Certified Arborist® exam. Expect questions on measuring DBH, sizing protection zones, fencing, and alternatives to trenching such as boring under the roots. You can try the other domains in the free practice test.
Test yourself: an exam-style question
A tree with a DBH of 30 inches has a critical root zone (CRZ) radius of:
- 15 feet
- 20 feet
- 30 feet
- 45 feet
Show answer
C. 30 feet
The common CRZ rule is 1 foot of radius for every inch of DBH, so a 30-inch tree gets a 30-foot radius, a protected circle 60 feet across. Stricter local rules that use 1.5 feet per inch would give 45 feet, which is why you check the code that applies to the site.
Questions like this come up in the Trees and Construction domain of the ISA Certified Arborist® exam.The 963 questions in the app each come with a written explanation.
FAQ
- What is the critical root zone of a tree?
- The critical root zone (CRZ) is the area around the trunk that holds the roots a tree most needs to stay healthy. The most common rule sets its radius at 1 foot for every inch of DBH, measured from the trunk, so a 20-inch tree has a CRZ about 20 feet in radius. Some local codes use 1.5 feet per inch or the dripline instead.
- How do you calculate DBH from circumference?
- Measure the circumference at 4.5 feet above the ground and divide it by pi (3.14). A trunk 63 inches around has a DBH of about 20 inches. A diameter tape does the division for you: it is printed so you read diameter directly.
- What is the difference between the CRZ and the tree protection zone?
- The CRZ is a formula radius based on DBH. The tree protection zone (TPZ) is the area actually fenced off for a project. It is at least as large as the CRZ and is often sized up for species that tolerate construction poorly and for older trees.
- At what height is DBH measured?
- In the United States, DBH is measured 4.5 feet (1.37 m) above the ground. On a slope, leaning trunk or trunk with a bump at that height, follow the adjustments in the guide on this page.
Sources
- American Forests. Champion Trees Measuring Guidelines Handbook
- City of Portland. How to measure a tree
- Washington State DOT. Standard Plan H-10.11, Tree Protection Detail
- Chattanooga Tree Commission. Tree Protection BMPs for Contractors and Builders
- Colorado State University Extension. Tree Preservation During Construction (after Matheny and Clark, 1998)
Checked against these sources on October 30, 2026. For education and ISA Certified Arborist® exam preparation only, not a substitute for ANSI standards, local regulations or professional judgment. Everything runs in your browser; nothing you enter is sent anywhere.